Fire extinguisher as co2 cylinder

The ins and outs of putting your beer into kegs.

Fire extinguisher as co2 cylinder

Postby Hillbilly » Tuesday Aug 30, 2005 12:32 am

I have a co2 fire extinguisher filled with 'BOC beer gas' to gas my new kegs but stumbled upon an issue reading another forum, some say that it's better to remove the inner dip tube when using for homebrew set up. Anyone know if leaving it in would give any dramas?
Hillbilly
 
Posts: 102
Joined: Sunday Feb 13, 2005 5:08 pm
Location: Gooseberry Hill, Perth

Postby munkey » Tuesday Aug 30, 2005 1:50 am

I'm not 100% on this one, but i believe that stored co2 is a liquid, and a dip tube would draw off liquid co2 from the bottom of the bottle, this would cause dramas as its likely that the liquid co2 would get in your kegs and proceed to create a bomb.

again not 100% but i think the principle of the co2 fore extinguisher isn't to release co2 at a managed rate as in brewing etc, but to dump as much co2 as possible into the area.
8) englend victorious "ashes 2005" 8)
munkey
 
Posts: 221
Joined: Thursday Jan 20, 2005 4:08 am
Location: united kingdom

Postby Dogger Dan » Tuesday Aug 30, 2005 2:20 am

Never had an issue.

To address Monkeys concerns, as you are running it through a two stage reg which is dropping the psi to about 10-15 from 9000, it will be a gas.

Dogger
"Listening to someone who brews their own beer is like listening to a religous fanatic talk about the day he saw the light" Ross Murray, Montreal Gazette
Dogger Dan
 
Posts: 3168
Joined: Thursday Aug 26, 2004 10:43 am
Location: Lucan, Ontario, Canada

Postby grabman » Tuesday Aug 30, 2005 9:17 am

Shouldn't be a problem Hillbilly!

AS Dogger says the reg will drop pressure down. IF you're worried though contact MythBusters, they're always looking for things to blow up!!!!
Some people say I have a drinking Problem....
I drink, I get drunk, I fall over....
What's the problem?


http://www.brodiescastlebrewing.com/
grabman
 
Posts: 1080
Joined: Wednesday Sep 29, 2004 11:38 pm
Location: Perth, Australia

Postby Hillbilly » Tuesday Aug 30, 2005 9:32 am

Thanx guys, I have the same fear as Munkey, sure the regulator adjusts the pressure to the keg but more the problem of the tube sucking up any co2 fluid left at the bottom of the cylinder, Dogger u still left your tube in there and havent had any problems?
Hillbilly
 
Posts: 102
Joined: Sunday Feb 13, 2005 5:08 pm
Location: Gooseberry Hill, Perth

Postby Dogger Dan » Wednesday Aug 31, 2005 2:25 am

Yes, It has been fine.

My biggest concern ironicly is the beer flowing backwards into the reg and dinking it up so I put a one way valve in after the reg as well as an isolation valve

That being said, I have never had beer flow back into the line either

Dogger
"Listening to someone who brews their own beer is like listening to a religous fanatic talk about the day he saw the light" Ross Murray, Montreal Gazette
Dogger Dan
 
Posts: 3168
Joined: Thursday Aug 26, 2004 10:43 am
Location: Lucan, Ontario, Canada

Postby Browndog » Thursday Sep 01, 2005 5:11 pm

I went the FE route and was in the same situation Hillbilly, I was told that the liquid CO2 could damage the reg, so I turned my extinguisher upside down so the dip tube fed gas only, then removed the dip tube once the bottle emptied. But from Dogger's experience this does not seem to be a problem.

cheers

Browndog
Browndog
 
Posts: 3
Joined: Wednesday Jun 22, 2005 5:24 pm

Re: Fire extinguisher as co2 cylinder

Postby Loose Canon » Tuesday Nov 18, 2008 8:10 pm

Just set up a system using a fire extinguisher and a mig welding reg. Was told at a homebrew shop it wasn't possible, all works well. i couldnt be happier.
Never argue with a mug!
Loose Canon
 
Posts: 1
Joined: Saturday Aug 05, 2006 12:08 am


Return to Kegging

Who is online

Users browsing this forum: No registered users and 12 guests

cron